HomeGenie Forum

General Category => Troubleshooting and Support => Topic started by: niva21 on March 26, 2015, 11:27:09 PM

Title: How to do install Philio Pan04
Post by: niva21 on March 26, 2015, 11:27:09 PM

Good Evening. am new to the forum and new to HomeGenie.
I have read how to install the module Philio pan04 but I do not automatically adds two virtual nodes to relay 1 and 2 but only the command for both. Use a raspberry with razberry.
In the configuration page form you need to set some parameters?
Thanks to all

Title: Re: How to do install Philio Pan04
Post by: nolio on March 29, 2015, 10:18:02 PM

Hi,
did you try the "get" button in the configuration of your philio ? (with a wake up of your philio).
Bye

Title: Re: How to do install Philio Pan04
Post by: niva21 on April 01, 2015, 09:47:52 PM

Hello. Nolio
thanks for the reply
The device is recognized correctly.
In the configuration of the device if I query manually instances work.
I hope that I spiegato.Allego screenshot.

Title: Re: How to do install Philio Pan04
Post by: niva21 on April 12, 2015, 09:45:01 AM

Hello everyone,
still can not see multiple instances in my group where I added the module Philio Pan04. In the settings module
I can query the instances and are ok. Suggeses?
I enclose full screenshot

Title: Re: How to do install Philio Pan04
Post by: niva21 on April 16, 2015, 12:15:19 AM

Hello,
no one can help me to solve the problem?
thanks

Title: Re: How to do install Philio Pan04
Post by: dani on April 18, 2015, 04:10:01 PM

For multi instance module, you have to activate the program with PID 93 (Multi Instance/channel virtual module) to create the 2 virtuals modules as chown in the following screen shot.

Cheers
Dani

Title: Re: How to do install Philio Pan04
Post by: niva21 on April 19, 2015, 11:28:31 AM

Hello Dani
thanks for the reply, but the program MultiIstance / virtual channel modules pid 93 is active.
My setup is:
 raspberryB+ with razberry and latest version of HomeGenie.
If I can spend a little of your time to solve the problem if you would be grateful.
Thanks
Greetings
Alberto

Title: Re: How to do install Philio Pan04
Post by: maccosx on August 08, 2015, 03:56:46 PM

Hi,

same issue here, just installed a PAN04 dual relays, program pid 93 (multiinstance/channel virtual modules) already active, added to zwave controller, recognized as multi instance but no virtual modules created.

i can get and set values from the confiuration page of the module but i cannot manage it as two separate virtual modules from dashboard.

is there a way to create manually virtual modules? Or another way to force creations of virtual modules ?

thanks
Cristiano

Title: Re: How to do install Philio Pan04
Post by: maccosx on August 18, 2015, 10:01:07 PM

i finally got my virtual modules.

i noticed that the program pid 93 is looking for parameter "ZWaveNode.MultiInstance.SwitchMultiLevel.Count" or "ZWaveNode.MultiInstance.SwitchBinary.Count" in every zwave module. As soon as one of this two parameter is > than 0 or as a number and is not empty it will create virtual modules as much as that number is.

i noticed that in my case was not working because i had that parameter (switchbinary.count) listed in the module prorpeties but it was empty, so i inserted "2" as value, i stopped and started again the program pid 93 and it created virtual modules you can then configure as you want.

Cristiano