HomeGenie Forum

General Category => Troubleshooting and Support => Topic started by: duch on August 30, 2014, 11:55:20 AM

Title: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: duch on August 30, 2014, 11:55:20 AM: Hello,

I've bought 7 Vision Security ZD2102EU Door Sensors

You can find some information about this product here http://products.z-wavealliance.org/products/702 (http://products.z-wavealliance.org/products/702) or here http://www.pepper1.net/zwavedb/device/357 (http://www.pepper1.net/zwavedb/device/357)

I'm using XP OS and Homegenie 1.00 beta r411

I have included these sensors in my zwave network without any problem ...

In association mode, i can configure the settings and get the manufacturer specific information
Quote
0109:2001:0102
, the battery level and the basic value - 0 and 255 respectively when the door is open or closed - :)

But after a few seconds, when the association mode becomes off, the sensor doesn't detect the level anymore and the basic value stays on 0 ???

I've tried to uninstall/install Homegenie many times and i've got the same problem for each of my 7 Vision sensors.

I have another Aeon door sensor wich is working fine.

Maybe, am I doing something wrong ?

Has someone experienced this problem ?

Thank you for your help

Best regards
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: naps1saps on September 01, 2014, 06:05:58 AM: I've had this problem after updating. If I go into the device settings there is no info for the device. Try waking the device and press get in the device settings of HG. Seemed to help fix my problem.
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: duch on September 01, 2014, 07:28:46 AM: Thank you for your answer.

I have done this many times, but it didn't work even with v394.

But you give me an idea. I have an older version installed on another computer. I'll try with it.
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: chgil on November 25, 2014, 09:54:37 AM: Hello i have this problem with ver. 421 the last update

there is a solution???

thanks
gil
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: chgil on December 01, 2014, 10:43:48 PM: Version 431 no resolve this problem did you have a solution???

Thks gilberto
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: duch on December 02, 2014, 06:53:05 AM: Unfortunatly, I've not tried this update.
I'll try it in a few days.
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: chgil on December 05, 2014, 06:15:25 PM: Unfortunately I can not run this sensor model and since it is at a good price seemed like a good solution, but with home genie does not work, no one who is able to give me a solution, I'm forced to change sensors or find other software to do these sensors work ????? Bahhh !!!!!

:-[ :-[ :-[ :-[ :'( :'( :'( :'( :'( :'(
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: chgil on December 23, 2014, 11:59:39 AM: NEWS????

THKS
Title: Re: Problem with Door/Window detection - Zwave Vision ZD 2102
Post by: kevin1 on December 15, 2015, 07:45:35 PM: This is old topic but I have new GoControl door sensors that look very similar to the picture of this device in pepper db. Did you get these to work? The GoControl WADWAZ-1 is also under different companies such as Nortek, 2GIG and Linear. None of these show up in pepper db.