CM15PRO - worked with HG but not working of late

[Gene]

I am not sure this will solve your issue, but if you want to try from scratch, use a wheezy image. With Jessie there will probably be issue with the startup script.

[emerich]

Hi all,
after a clean installation (OS and application) it works for me again also with the latest build 499. Can't tell you why, but I'm happy! 

br. Christian

[chrispazz]

Wheezy?

[bkenobi]

Please provide some basic description of what you did.  I base my installation off the most recent RPi image Gene posted (very old now).  If it's better to install Raspian or Wheezy or something else, that would be good to know.

[Gene]

Raspbian Wheezy

https://www.raspberrypi.org/downloads/raspbian/

[Jens]

All,

I have CM15pro connected to raspberry Model B without any issues with X10 devices. From my point of view there is no need to revert any recent changes in XTenLib.

Devices I have include switches, dimmers and shutters as well as X10 RF motion sensor.

Regards
Jens

[petediscrete]

Raspbian Wheezy Kernel 3.18.11+ #781 PREMPT Tue April 21 armV61.
Raspberry PI Model B.
In use: HG 1.1 rc499
Attached: CM15Pro x10 light and appliance modules. RPI CSI camera module.
Everything working so far.


Word is, avoid Jessie for the moment.

[bkenobi]

I'll try updating the system in case that's the issue.  I don't see why this is an OS issue since in my case the CM15A works mostly and it works 100% with the older versions (e.g., r493).  My issue may be slightly different and is described here:

http://www.homegenie.it/forum/index.php?topic=1148.0

[chrispazz]

I partitioned the old SD Card, installed Wheezy from scratch, updated Raspi-config and installed 1.1 r499.

CM15Pro is running ok now.

[emerich]

Sorry for being late, thats exactly what I did. A clean installation from scratch. I'm using mono 4.0.4

br. Christian

[bkenobi]

I installed a new copy of Wheezy (5/5/2015 I believe is the latest) and HG.  With both 499 and 500 I still have partially working CM15A.  It works, but when it receives commands there is a 5-10 second delay because HG is not communicating with the controller correctly and resends the command 1-2 times.

For those that found that starting from scratch fixed the problem, any guidance on exactly what you installed would be helpful to figure out what I (and others) are doing differently to get a different result.

[lowerider]

I can't say I am saving the same error but I am getting a 'Object reference not set to an instance object' error message. I am running HG r500 on Windows 7.  R491 worked for me but i wanted to try and upgrade. This is the message, it does not seem to be updating the log even though HG is running. I cannot access the website at all. Just wanted to through this out here since it looked like the bug was being worked.

2015-11-15T10:48:48.3876725-05:00   HomeGenie.System   Console   StdOut/StdErr redirect   Console.Output   System.NullReferenceException: Object reference not set to an instance of an object.
   at MIG.MIGService.webGateway_ProcessRequest(Object gwRequest) in c:\Users\IEUser\Desktop\HomeGenie\MigFiles\MIG\MIGService.cs:line 477
   at MIG.Gateways.WebServiceGateway.Worker(Object state) in c:\Users\IEUser\Desktop\HomeGenie\MigFiles\MIG\Gateways\WebServiceGateway.cs:line 217
2015-1